, , , , , ,

Do-It-Yourself His and Her’s Towel Hooks

Being married means sharing things, right? Like a bed, his last name and the household finances. But, there are some things that are off limits – like my bath towel! I loathe getting out of the shower to find my towel damp. Don’t you?

So to rectify this problem, I can’t think of a better way than to “label” your towel hooks! Thus, the perfect use for these adorable vinyl designs from Simply Said – the MR. and MRS.

I love them, and think every married couple should have them! Imagine the uses – iron them on your bed pillows, adhere them to your mirrors above a double vanity, or mark the bride and groom seating at a wedding ceremony!

Here’s the easy steps to making your own:

1) Order your Simply Said vinyl designs here.  Mrs. is item #NP1090, and Mr. is item #NP1089. You choose the size and color. I chose 10″ in Warm Grey. They’ll take about 10 days to arrive.

2) While you wait go shopping for a piece of wood. I went to Lowe’s and bought a 10×1 board and had them cut it down to several pieces that were 10×10. The first two cuts are free and every cut thereafter is just twenty-five cents.

3) Buy two hooks (these came from Lowe’s), and two picture frame hangers for the back of the board (to hang on the wall).

4) Lightly sand your corners and edges, as the cuts are raw and splintery. I used a Black and Decker Mouse to sand with  80 grit paper, followed by 220. Remove saw dust with a dry brush.

5) Paint your boards. I chose to use Annie Sloan Chalk Paint in Emperor’s Silk. After I painted the wood (two coats), I applied dark wax, and distressed the corners.

6) Allow your paint and wax to dry fully. It’s best to allow them to “cure” for a week or two, so all the chemicals evaporate before you apply the vinyls.

7) Once your painted boards are ready, apply your vinyl designs. See the application video here.

8) Follow the directions for putting your hooks on the boards. Basically its just a matter of using an electric screwdriver to drive two screws through the hook hardware into the wood.

9) Follow the directions for putting the hanging hardware on the back.

Done! Now hang them in your bathroom and be sure to show the love of your life his or her new towel hook!

, , , , , , , , , , , ,

Simply Said at The Empty Nest

Today I had the pleasure of doing a Simply Said party with Janet from The Empty Nest – a delightful  shop that sells Annie Sloan Chalk Paint. Janet and I go back a few years — I had met her during Annie Sloan’s US tour, when she was in Leesburg, VA. I was attending and brand new to chalk paint. Someone introduced her to me as my local stockist (back then she was a booth-holder in an antiques shop). Now Janet has a gorgeous shop full of amazing furniture and goodies in Old Town Warrenton, VA. When I was painting furniture I was in her shop almost weekly. Talk about inspiration – check it out!

Ahhh – the mother lode!

Janet’s shop is a feast for the eyes! She has chalk paint, antiques, painted furniture, hand-crafted items, repurposed items, lovely textiles, and so much more! I could browse for hours!
She was so kind in offering to host a party for me in the shop. I set up in the back and we had a nice crowd join us to learn how to use Simply Said in their decorating. Here’s a few shots from the party!
Janet put out quite the spread!
 I loved the welcome sign!!
My Simply Said display included a few painted items, as well as Simply Said’s accessories and designs.
 In this picture I am removing the grid paper from the back of a design.
Here I am demonstrating how to easily hang a design on the wall. 
I had such a nice time chatting with the women who came. I loved hearing their ideas for using Simply Said. One lady, named Sue, is planning on creating a custom design using Simply Said’s online tool, called Your Way. She’s going to make a back-splash design that I have no doubt will be the conversation piece of her kitchen!
This was certainly a fun venue for a party! Big thanks and appreciation go out to my friend, Janet! if you’re in the Warrenton, VA area, be sure to check out The Empty Nest!
, , , , , , , , , , ,

A simple Welcome Sign

Looking for an easy-to-make “Welcome” sign? I made one today and thought I’d share the simple steps.

First, find an old kitchen cabinet door. You can get them a few places. Try searching Craig’s List – a lot of people give them away for free when they are redecorating. Or search your local Habitat for Humanity restore. (find a list of stores here)

Then paint it to your heart’s desire. I used Annie Sloan’s chalk paint. Here’s a video of Annie on The Hallmark Channel doing a tutorial.

The next thing I did was apply a Simply Said vinyl “welcome” design. And here’s a video showing you how easy they are to apply. This is so much easier than the way I used to apply designs or enhancements to my painted furniture, which comprised of time-consuming transfers or stencils.
Here’s my Simply Said website, where you can order a welcome design. I think this would be a great idea for personalizing with your family last name and the date you moved into your home, i.e. “Peterson Est. 2010.”  Or even a sign for a wedding, with a design that says something like, “Matt and Nikki, April 21, 2014.”  You get the idea – the possibilities are wide open!

My last step was to drill two holes through the wood with a standard drill bit, and run a ribbon through for hanging. Voila! A simple, fast way to spruce up a front door, entrance, or anyplace in and around your home.

, , , , , , , , , ,

Applying a Simply Said vinyl design to chalk painted furniture

When I was painting a lot of furniture, I loved putting designs on them. Chevron was very popular. So was anything french, Paris or script-inspired. It still is. The problem for me, was that I was relying on stencils to achieve the look. With stencils, I always had a little paint bleed-through and could never achieve the crips, clean edges I desired. Transfers were another option (using tracing paper to imprint a design onto a painted surface), but they took forever to fill-in with paint. And again, my hand wasn’t steady enough to get the crisp edges I wanted.

BUT NOW – there’s a solution to the edge issue. And a big time-saver. It’s vinyl designs. I just applied my first Simply Said design to a little side table and I LOVE it! It took a whole 3 minutes to apply!

Here’s the easy steps to applying the design:

1) I applied it over a piece that was painted with Annie Sloan’s chalk paint in Old White, with clear wax.

BEFORE

 I ordered the design in a grey color that looks a lot like Annie Sloan’s Paris Grey. Look how pretty it is!

Next, I laid it grid-side facing up and ran the application tool across the entire surface to rid it of air bubbles.

 Then I began in the top corner and slowly pulled the grid paper back and down to remove it.

Next, I laid it over my table.

Then I used the application tool again by running it over the whole surface to remove air bubbles and flatten it to the table.

I started at the top left corner and pulled the paper back and down to remove it slowly.

And there she is! Pretty!

It really looks like its painted on! I couldn’t be happier with it!

, , , , , , , , , , , ,

A Nelson Matter Dresser Makeover

I picked up this dresser and mirror several months ago at an auction.

As you can see, it was a mess. The lovely crackled finish would have been nice to leave as is, excerpt there were places on the top, front and sides that had huge areas of damage. The top had cup rings, the front looked like a tire tread over the paint, and the side had business cards stuck to the surface!

After inspecting the inside when I got it home, I discovered this medallion in a drawer.

It belongs to The Nelson Matter Furniture Company, which had been established in 1844 in Grand Rapids, Michigan. After a little research online, I discovered this company went out of business in about 1910. So, you can see that this is an old piece of furniture! And that would explain its sold wood, dovetailed construction, as well as the state of the mirror, which is quite cloudy. However, it certainly doesn’t deter from the beauty of the piece, but gives it more character in my opinion. I loved the bail pulls, even though it was missing one. I loved the keyholes, the swiveling mirror and gorgeous legs. I loved it at first sight, and waited through 4 hours of bidding to get it!

After giving it a quick clean-up with mineral spirits, I decided to paint this with Annie Sloan Chalk Paint. I used Graphite with dark wax, as well as Paris Grey with clear wax (the two-tone look is so hot right now). And while I had hoped to find a drawer pull to match the existing ones, my search came up empty-handed. So, I ordered 6 new solid brass rosette bail pulls, that were a close match.

And here she is…

I love painting dressers – especially old ones. They always please me to no end with their dramatic transformations! I hope this beauty finds a well-deserved new home!

, , , , , , , , , , ,

Do-It-Yourself Framed Canvas Project – From an Ordinary Photo

Last night was our monthly craft club meeting. Our lovely neighbor Tara hosted, and she taught us how to turn a regular photo into a framed work of art! As a professional photographer, Tara has a houseful of amazing photos that I thought were printed on canvas. One hanging in her hallway is stunning, and inspired this month’s meeting!

I know its hard to see in photos, but when you walk up close and touch the surface, they have the delicate texture you find on a canvas. Last night, she let us all in on her secret. And now you can craft your own canvas look-alikes, too (for a fraction of the price I might add)!

Here’s what you will need:
-A standard printed photo of any size (a great place to get prints at really reasonable prices is Costco)
-A frame
-A piece of foam board (you can buy this by the sheet at any craft store with a framing section)
-Mod Podge and foam brushes for applying
-A straight edge, cutting board and exacto knife (if you need to cut down your photo, or foam board)
-Sponges
-Rolling pin thingy
-Black and gold paint (optional)

2) First, find a photo you like and get it printed in the size you desire. 
Ever since a trip to Luckett’s 2 years ago, I have wanted a huge piece of art with a white horse on it. They had a gorgeous framed arabian horse, and wow – I stared at this beauty. But the price tag was insane! I haven’t forgotten that horse, so when this opportunity to make my own big piece of art came along, I hopped on a stock photography website to find my own white horse. I used Shutterstock. I was able to purchased and immediately download a “Super” high-resolution sized image (28.6″ x 19.0″ at 300 DPI) for only $19!! Once I downloaded the image from Shutterstock, I then uploaded it to the Costco photo center website. There I opted to printer a poster-sized photo in 30″ x 20.” This only cost $8.99! And it was ready in just a few hours!
3) Find a frame. Ideally, you want your frame to be the same size as your print. But, if your photo is bigger than the frame, you can always cut it down. Simply use a straight-edge or ruler, cutting board and exacto knife to get the size you need. Cut your foam board to the same size as your print.
Here’s a tip – custom frames can be outrageously expensive (Trust me – the one I wanted for this project from Michael’s was $400!) So, there’s a few things you can do, buy a plain frame and paint it, which is what I did. Or, go to a place like HomeGoods, and score a clearance mirror and just remove the mirrored part. Instant frame!)
4) Once your print and foam board are cut to the correct size, gather your Mod Podge (we all used Matte, but Glossy is also available), a foam brush, and the rolling pin thingy. Liberally apply mod podge all over the foam board, creating a smooth layer. Cover the entire piece and make sure to get the edges. Here’s Tara demonstrating!
5) Next, place your print over the foam board, and begin smoothing it out with the rolling pin thingy. Try to remove any and all air bubbles. Move in all directions. Once you have it smoothly in place, allow it to dry. This might take about 10 minutes – it dries rather quickly. At this point, we stopped to enjoy Tara’s delicacies, which included homemade candied walnuts (to die for)!!

Isn’t this a great photo? Another one of Tara’s awesome shots!

6) After it dries, here comes the fun part…
Spread another liberal layer of mod podge right over the print. Work quickly, so it doesn’t dry, because you immediately want to “stipple” the mod podge with a sponge. We used everyday dish sponges, that were split down the middle to reveal the bumpy texture inside. You can used other sponges, too – choose the size of the holes you prefer. Some sponges create larger stipple, while others create a smaller, finer stipple. We all opted for these dish sponges, which made larger stipple.
 Quickly dab the sponge on the wet mod podge. Dab the whole print, until you see the texture everywhere.

You dab fast, hence the speedy hand photo here!

When you are done, your entire print will look like this. Don’t worry, the mod podge dries clear, and will only leave behind the texture – giving it the canvas look! We waited for it to dry, and then went back and did a second layer of the stippling.

Here’s the white stippled mod podge on my horse.

After they dry, you simply insert your piece into the frame!

Here you can see the texture well in the top-left corner! Liza made this work of art!
She also made this one of her wedding bands on the beach – again you can really see the texture on the shaded areas in the bottom right.
Here’s Tara’s – isn’t the frame awesome! It was originally a mirror!

Here’s two Kelly did!

And Kim’s shot from Hawaii!
Now that we’ve told you how this is done, let’s talk about a few “special techniques,” for aging your photos. Kristi worked on these two dog images as a special memento for her parents who just lost their beloved pets. Since her original photos were a bit blurry, she wanted to make them look old and “grainy,” like a lot of old photos used to be back in the day. For the Photoshop users out there, you would called this adding “noise.” To achieve this noise, Kristi added a tiny bit of black craft paint to her mod podge, stirred well, and then stippled. You can really see it well on the right-hand shot.  They turned out great!
In this photo Tara showed us how to age a piece two ways. She watered down a gold craft paint, and sponged it all over the image. You know how photos tend to turn yellow over the years – she made it happen instantaneously! Then she used watered-down black craft paint to create a silhouette around the edges. So cool!

Tara turned her kitchen into a serious studio for us with long tables covered in paper!

Here she is demonstrating the aging techniques!
Since my horse piece was so big, I needed help to get it smoothed out quickly and remove the air bubbles before the mod dried!

I LOVE how it turned out. I know its really hard to see the texture in my photos, especially on the white areas – but trust me, its there, and it feels so cool!

Remember how I said you could paint your frame? That’s what I did here…finding a cool 20×30 frame or mirror was impossible. I could only find a plain black one. So, I dry-brushed a couple of Annie Sloan Chalk Paint colors over the black, and it changed the whole look. I can’t wait to hang this in my home!
Thank you to Tara for all of her hospitality, and for teaching us how to make our own custom-canvases! I know I will be doing this again and again!
, ,

The decoupaged document dresser

Say that three times fast! (I love a good tongue-twister)

Here’s one of my latest paint projects – an Ethan Allen dresser with matching mirror. It started off a golden honey color, and now looks like this:

I painted the whole thing in Old White. It’s heavily distressed and sealed with clear wax. Dark wax was added for aging. A while back I ordered several rolls of document wrapping paper from Ballard Designs, and this piece was begging for something different. A little Mod Podge and the drawer fronts got a cool new look. And to make it even more unique, I pulled out the BBQ lighter and scorched the edges of each piece of paper. (my house stunk for days!)

What’s next? I’ve got a couple of unfinished wall cabinets to do for a client, and a girly toy box to personalize with stencils for another. My own stash includes two twin beds to finish, and two antique chairs to paint and reupholster! I seriously gotta buckle down and get in the garage! Later friends!

, ,

Vintage Radio Cabinet Transformation

Last year a neighbor, who was moving, gave me this vintage radio cabinet. The guts had been removed before she purchased it, but she had plans to use it as a decorative shelf/cabinet. She never had the time, so she gifted the piece to me (thank you Karen!). And as well all know, kids/work/home/life can take over, and the neglected radio cabinet sat in my garage for nearly 6 months before I finally put some paint on her! But here she is all prettied up!

I painted her with Annie Sloan Chalk Paint in Provence, and sealed with clear soft wax. Dark wax gave it some aging, while fresh fabric now livens up the area where the speaker used to be. I also stripped and restained the top in a dark walnut, and wiped on some poly for protection.

Wouldn’t it be a great conversation piece in your entertainment area/basement? The back is open, and there’s a piece of wood inside that would work as a shelf for your I-Pod dock. You could hide your player inside and little would anyone know that the music coming out is from your I-Pod!

Ahh, it would be a marriage of today’s technology with yesteryear’s beauty!

, , , ,

Painting a Chandelier

I found this chandelier during a trip to a local consignment shop. It was hanging and I almost didn’t notice it. The dark color, the dinginess of it – it faded into the background. It had been there for several months, so I was able to negotiate the price down to $25.

I’d been on the hunt for a chandelier to make over. I wanted one that was delicate, yet not too feminine. I love the blingy, crystal-adorned chandi’s out there, but figured my hubby wouldn’t be crazy about something so girly. So the simplicity of this one above looked like it could work. And I was hoping that with a paint job and new candle covers, I could give this a weathered look, similar to these below.


I adore similar light fixtures found at places like Pottery Barn and Restoration Hardware. So I was hoping I could get close to the same look, without the price. 
What do you think – did I come close?

I started by painting a base coat of Annie Sloan Chalk Paint in Paris Grey. Then I dry-brushed on Coco followed by Old White. Next I clear waxed the whole thing. Normally I don’t think its necessary to wax a light fixture like this, because the paint won’t risk getting wet, touched or damaged. But, I wanted to age this with dark wax, and I prefer how it looks when its applied over clear wax, vs. straight on the paint.  I used a cloth to apply the clear wax to the entire thing, wiping it away. Then I used a small brush to apply dark wax more sparingly. Afterwards, I painted and waxed new candle covers. It was only when I started to put new bulbs in did I realize one of the sockets was damaged. So, it will have to be repaired before I can hang my new chandelier. Now to find myself an electrician!
, , , , , , , , , , , , , ,

The Joy of a New Color

My latest custom paint project was pure joy! The main reason is because I used a color I haven’t tried before and OH. MY. GOD….it made me giddy after just one coat! Take a look. Tell me this transformation doesn’t make your heart sing!

BEFORE
My client, Lauren, was in the market for a vintage buffet, and I had spied this beauty from a fellow furniture guy on Facebook. I directed her to his site, and the rest is history. She had me over to take a looksy at the piece in her home, and we decided this baby was going to make a statement!
AFTER
 Painted with Annie Sloan Chalk Paint in Aubusson Blue! (do you hear that, angels are singing)
The inside was done in a 50/50 mix of Old White and Old Ochre. There was a ton of bleed through on the inside, as the original wood was stained but unfinished. So I had to use clear shellac to block the bleeding and used a few more coats of white than I normally would. But, I gave it lots of texture, and really aged the inside. I love that look.
Everything was sealed with soft clear wax and aged with dark wax. Seriously, what doesn’t look better with dark wax!

This is the original hardware, believe it or not. I tried to clean the dark stuff that was on each pull with Brasso, but it revealed a dingy silver color under the muck. So, I pulled out some gold gilding paste and gave them all a little bling. 
I have been out in the garage swooning over this buffet. Craig’s List has been up on my laptop all day, so I can find a buffet of my own to paint in this color! When the right piece comes along, I’m telling you, I might just redecorate my living room so I can have something big and gorgeous in Aubusson Blue!!